A Step-by-Step Overview to Installing a Bath Tub
A Step-by-Step Overview to Installing a Bath Tub
Blog Article
Here down the page you can find a good deal of incredibly good points pertaining to Tools You Need to Install a New Bathtub .
Installing a bathtub isn't exactly rocket science, yet it does require strong plumbing, woodworking, as well as often, tiling abilities. Changing an old tub with a new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the task can relocate speedily; if you need to open up a wall surface to get rid of the old bathtub as well as place the brand-new tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have qualified yourself for the job and also fit attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to think about utilizing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly help you mount a new bath tub in your shower room if you have currently bought a brand-new tub as well as don't require to change the arrangement of your previous water supply pipelines.
Your tools and also product checklist need to make up the following:
Getting ready for the Installment
First of all, the sustaining framework provided with the bath needs to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to stop strain on the bath tub.
Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its final position.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of getting rid of the existing taps can be rather bothersome as a result of the restricted access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Using the two wood boards under its feet, position the tub in the needed setting. The wood boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level checks out level.
To install faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Turn on the supply of water and check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and also examine the overflow electrical outlet and the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has been used at least when as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, causing the water to permeate the wall surface between the bathroom and also the tiling, resulting in issues with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to permit the activity experienced when the tub is in use. The sealer can split rather early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very involved in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you liked my post. In case you enjoyed our page if you please make sure you remember to share it. Thanks a lot for your time. Don't hesitate to come by our site back soon.
Pricing
Report this page